How to Program Garage Door Remote?

By
reviewed
Reviewed by
Last updatedLast updated: May 17, 2021
Wise Pick is reader-supported. We may earn a commission through products purchased using links on this page. Learn more about our process here

You have recently bought the car of your dreams: since your home is equipped with private parking protected by an electronic gate, you need to obtain a copy of it. This is necessary if there is an emergency, the present one gets missing, or you have to grant your spouse or a friend access to the garage in your absence. Well, we are happy to inform you that you are in the right place, in a moment that could not be better: in fact, below we will explain to you in detail how to program your garage gate’s remote control, whether it be Liftmaster, Chamberlain, or Craftsman brands.

Don’t worry if you have never done this before, and you have no reason for a prior experience. Modern remote controls are equipped with self-learning features, so you will not need special and expensive tools to achieve your goal or skills. Without hesitating, grab a cup of coffee, follow through with this blog and get to work immediately: you will see, the result will not leave you disappointed. That said, there is nothing left for me to do but wish you good reading and, why not, good work!

How Does Remote Work?

How to Program Garage Door Remote?The principle of operation of the garage remote is quite simple. Among its features are the following points:

  • There are two main devices: a receiving signal and an emitter. These two work in tandem – the emitter sends a signal to the installed drive, and the door structure moves.
  • A signal emanates from the emitter, which controls the garage door opener.
  • The electrical part of the remote control is responsible for sending a signal to open and close the gate.

All this determines that the system works without any problems. In some cases, cheap devices become unstable, especially if there are other sources of radio signals nearby.

Step-by-step Remote Programming Guide

Before getting to the heart of this guide and explaining how to duplicate the gate remote control, it is good that we provide you with some valuable information about this topic. First of all, to copy the remote control, you must make sure the original device is working, adjusted to the correct transmission frequency, and with the battery sufficiently charged. You can easily carry out this check by pressing the opening button within the gate control unit’s reception range and checking that the latter opens correctly.

For the copy to be successful, you must make sure that both remote controls (the one already tuned and the one to be tuned) support the same transmission frequency. In most cases, the electronic control units marketed in the US mainly receive signals emitted on a frequency of 315 MHz, so make sure your “target” remote has support for that transmission mode.

To program the remote

  1. The device to be programmed must be set in ‘ self-learning ‘ mode or, if this function is not available, just bring the two remote controls closer.
  2. The next step is to press both buttons of the device to be duplicated (the opening and closing commands) until they start flashing.
  3. After which, you need to keep pressing only the top key; meanwhile, the universal remote control (the new remote) must be close to the remote to be duplicated.
  4. On the other remote, press the upper key (or in any case the same one we are pressing on the other); once the light signal starts flashing once, it means that the key has been configured on the universal control.
  5. To also configure the key that controls the closing function (or vice versa if this was configured first), repeat the same procedure with reversed keys.
  6. The last step is to check if the duplication was successful; this is done by opening and closing the garage with the newly configured remote.

Suppose the new remote control just created doesn’t work. In that case, we suggest you first repeat the procedure, perhaps bringing the two remote controls even closer or moving to an area completely free of interference.

If, after several attempts, the transmitter is still unusable, check the effective operation of the original remote control, making sure that its battery is sufficiently charged.

Is it Hard to Program a Wi-Fi-controlled Unit?

A Wi-Fi garage door opener can be used instead of conventional units. They function with an application installed on your smartphone, making it incredibly easy to use. The question is, are all garage doors enabled to use this feature? No, but for garage doors manufactured after 1993, it is possible to use a device to program the Wi-Fi feature on your garage door. The Chamberlain B970 is an excellent example of such a device. Once you have purchased this device, its installation is pretty straightforward. You have to ensure you have a good internet connection in your garage, after which you install your device in the garage following the manufacturer’s instructions, and you complete the setup by downloading the MyQ app on your smartphone.

You might also want to consider installing a garage alarm with excellent security features. Our experts’ recommended pick is the Ring Floodlight Cam, with its alert and high-tech features that enable you to monitor what goes on in your garage’s environment and communicate with your visitors. You won’t regret checking it out!

Final Thoughts 

It’s our hope that now, you know how to program your garage door remote. It is an essential part of its security, and it makes parking more convenient. By following these easy steps, you will be able to use the full potential of the appliance you’ve recently purchased.

Leave a Reply

Your email address will not be published. Required fields are marked *